English
EnglishEspañolFrançaisالعربيةDeutschPortuguêsItalianoفارسیBahasa IndonesiaاردوTiếng ViệtBahasa MelayuRomânăΕλληνικάहिन्दीNederlandsTürkçePolskiไทยУкраїнськаРусскийČeština한국어বাংলা日本語简体中文繁體中文FilipinoKiswahiliSvenskaעבריתSuomiDanskMagyarNorsk bokmålதமிழ்

Your country is detected for each new visit. You can choose your country and language.

Satellite internet / Detailed guide

iDirect iQ Desktop+ Satellite Router · Exact manual and safe first checks

iDirect iQ Desktop+ Satellite Router · T0001107 Rev A; July 1, 2019

Applies to: iDirect iQ Desktop+ Satellite Router · T0001107 Rev A; July 1, 2019

Work through these checks

  1. 01 · iDirect iQ Desktop+ Satellite Router

    Match the exact model, product code and manual edition. Record the existing connections, status indicators and displayed error without changing them. Preserve settings and stored data; do not reset, flash software, format storage or alter wiring as a first check. Keep account details, device identifiers and precise location private.

  2. 02 · iQ Desktop+ / PWR / STAT / RX / TX / NET / NCR / Listening Mode / Level 0 / Level 1

    Identify iDirect iQ Desktop+ with the 52-page Installation, Support, and Maintenance Guide T0001107 Rev A, July 1, 2019; not iQ Desktop, iQ200 or another iQ model. One physical router, no software/component credits. LED meanings may vary by iDX release; match the installed release documentation, not the supplier folder name. Observe existing PWR/STAT/RX/TX/NET (printed 8–11). PWR green is power only; STAT half-second green flashing initializes, steady green completes initialization. RX steady amber means demodulator not locked; one-second amber flashing means demodulator locked but NCR not locked; steady green means both locked. TX steady amber is disabled, one-second amber flashing acquires upstream, steady green upstream acquired. NET one-second green flashing acquires the network, steady green network acquired, not guaranteed application internet. The over-current pattern is PWR steady green, STAT red flashing each second, RX/TX yellow flashing each second and NET off; BUC supply is off while LNB supply stays on. The source says this state can last five minutes or until intervention; do not induce it or intervene as a test. In Listening Mode, PWR/STAT/RX steady green with TX steady yellow and NET off still does not mean restored transmission/network (11). Stop and refer the observed pattern to the provider; arrange safe isolation before qualified cable inspection. TX feeds the BUC, RX receives from the LNB; UART's RJ45 is console, not Ethernet ETH1/ETH2 (10). Preserve wiring, options, IP/VLAN and RF settings. Level 0 reboots; Level 1 factory recovery has no in-place recovery and requires software/options/configuration reload (37–38); do not press reset or enter either mode. Do not commission/point, enable TX, issue commands, run traffic/tests/calls, change settings, reboot/update/reload or export/send reports. No live cable, opening, supply/voltage/fuse/battery work; do not interrupt a known update. Observe safe ventilation only; overheating can shut down the board (20), not permission to open or alter power. Protect IDs, IPs, positions and configuration. Supplier-hosted historical manufacturer original gives no current network, service, licensing or compatibility assurance.

When to stop and get help

Do not continue these checks in unsafe conditions. For immediate danger, use local emergency services and the device’s emergency instructions. Otherwise, contact your provider or a qualified technician.

What to tell support

Write down your exact model, service provider and on-screen message. Photograph the existing connections for your own reference before changing anything.

Original troubleshooting guidance based on the official sources below. Menu names can change. This is an independent guide, not a manufacturer service bulletin or a bench-tested repair.