English
EnglishEspañolFrançaisالعربيةDeutschPortuguêsItalianoفارسیBahasa IndonesiaاردوTiếng ViệtBahasa MelayuRomânăΕλληνικάहिन्दीNederlandsTürkçePolskiไทยУкраїнськаРусскийČeština한국어বাংলা日本語简体中文繁體中文FilipinoKiswahiliSvenskaעבריתSuomiDanskMagyarNorsk bokmålதமிழ்

Your country is detected for each new visit. You can choose your country and language.

Phones & messengers / Detailed guide

Thrane & Thrane TT-3020C / TT-3022D Capsat family · Exact manual and safe first checks

Thrane & Thrane TT-3020C / TT-3022D Capsat family · TT-99-107311-A Version A; printed release 11MAR97

Applies to: Thrane & Thrane TT-3020C / TT-3022D Capsat family · TT-99-107311-A Version A; printed release 11MAR97

Work through these checks

  1. 01 · Thrane & Thrane TT-3020C / TT-3022D Capsat family

    Match the exact model, product code and manual edition. Record the existing connections, status indicators and displayed error without changing them. Preserve settings and stored data; do not reset, flash software, format storage or alter wiring as a first check. Keep account details, device identifiers and precise location private.

  2. 02 · TT-3020C/TT-3022D / Power / Login / Send / Mail / Alarm / Set / OPTIONS - TRANSCEIVER STATUS / Synchronization / Logged in / RX/TX/AGC / B/S / Current protocol / BB error rate / Link Test

    Identify the legacy TT-3020C/TT-3022D family using the 62-page Technical Reference Manual TT-99-107311-A Version A, release 11MAR97; June 1996 is copyright. One message-transceiver family, no software/component credits, not voice/IP internet or later Stop panels. Only observe existing authorized indicators/status on the documented Set/Alarm panel. Power means DC present; Login steady means logged in, flashing means synchronized but not logged in, off means no synchronization (printed 19). Send flashes before transmission and while awaiting LES acknowledgement afterward, steady means transmitting. Mail flashes before non-EGC reception; automatic reading can make it go off immediately. Alarm is normally off; flashing/steady indicates distress awaiting/received acknowledgement, not permission to test or clear. Never press Set or Alarm, never enter Link Test: it can automatically send a distress test (3,19). In existing OPTIONS - TRANSCEIVER STATUS, distinguish Synchronization from Logged in (39–42). RX/TX/AGC combines present receive current, last-transmission current (zero can be normal before any transmission) and attenuation setting, not one quality scale. B/S separates potentially stale bulletin-board validity from signal strength 0–5, 5 best; BB error rate summarizes 100 frames/about 15 minutes (40–44). Read Current protocol only; Pending is deferred by the LES, not uniquely a hardware fault. Do not issue commands, scan/login/logout, transmit/call/message/test, acknowledge/silence alarms, change settings, export/send reports, reset/restart/update, move/open hardware, touch live cables or alter voltage/fuses/batteries. Do not interrupt known updates. Stop for damage; arrange safe isolation before qualified inspection. Protect IDs, positions and message content. Supplier-hosted historical original gives no current network, GMDSS, airworthiness or emergency-service assurance.

When to stop and get help

Do not continue these checks in unsafe conditions. For immediate danger, use local emergency services and the device’s emergency instructions. Otherwise, contact your provider or a qualified technician.

What to tell support

Write down your exact model, service provider and on-screen message. Photograph the existing connections for your own reference before changing anything.

Original troubleshooting guidance based on the official sources below. Menu names can change. This is an independent guide, not a manufacturer service bulletin or a bench-tested repair.