English
EnglishEspañolFrançaisالعربيةDeutschPortuguêsItalianoفارسیBahasa IndonesiaاردوTiếng ViệtBahasa MelayuRomânăΕλληνικάहिन्दीNederlandsTürkçePolskiไทยУкраїнськаРусскийČeština한국어বাংলা日本語简体中文繁體中文FilipinoKiswahiliSvenskaעבריתSuomiDanskMagyarNorsk bokmålதமிழ்

Your country is detected for each new visit. You can choose your country and language.

Phones & messengers / Detailed guide

ASE ComCenter II ASE-MC07 / ASE-MC08 family · Exact manual and safe first checks

ASE ComCenter II ASE-MC07 / ASE-MC08 family · Rev 1.1 [01-09-12]; 51 PDF pages

Applies to: ASE ComCenter II ASE-MC07 / ASE-MC08 family · Rev 1.1 [01-09-12]; 51 PDF pages

Work through these checks

  1. 01 · ASE ComCenter II ASE-MC07 / ASE-MC08 family

    Match the exact model, product code and manual edition. Record the existing connections, status indicators and displayed error without changing them. Preserve settings and stored data; do not reset, flash software, format storage or alter wiring as a first check. Keep account details, device identifiers and precise location private.

  2. 02 · ComCenter II / ASE-MC07 / ASE-MC08 / READY / ON LINE / CONNECT / DISCONNECT / ASE EVENT LOG / ASE NETWORK MONITOR / RESTART SYSTEM / NOT READY TONE / ALERT TONE

    Match ComCenter II to the 51-page Applied Satellite Engineering original Rev 1.1 [01-09-12], preserving that printed date without treating the distributor upload date as its edition. The shared family includes ASE-MC07 data-only and ASE-MC08 voice/data; optional GPS or handsets are not universal, and this is not ComCenter II Outdoor or a handset dock. Record existing indicators: the green satellite light should become steady after initialization/registration; the manual allows 5–10 minutes after initial power application, not a reason to power-cycle for a test. Continued or periodic blinking can mean failure to find or register with the network, not proof of a failed antenna. In an existing authorized web session, READY means a data connection can be established; ON LINE and the blue data light indicate an established data call. CONNECT automatically dials the ISP and DISCONNECT ends a session: do not press either as a test. Only read existing ASE EVENT LOG entries (last 100 events) and ASE NETWORK MONITOR information (updated every 15 seconds); do not clear logs, enable reports or use RESTART SYSTEM. Existing RJ-11/POTS tones concern ASE-MC08 only: NOT READY TONE can mean initialization or network search; an ALERT TONE with two beeps indicates missing SIM, three locked SIM, and four can mean either registration denied or bad SIM. Do not lift the handset, make test calls, enter PINs or change SIM/service settings to elicit tones. Ethernet and the privacy-handset interface are distinct ports despite RJ-45 connectors; preserve existing cabling and assigned network mode. Leave antenna visibility, cable loss and installation assessment to qualified service without moving the antenna or reconnecting live cables. No transmission, message sending, data sessions, AT commands, network configuration, reset/reboot/update, voltage, opening, roof or battery work; do not interrupt a known update. Protect subscriber identifiers, PINs, IPs, call/SMS logs and location. This distributor-hosted historical original does not promise current service, options, compatibility or approval.

When to stop and get help

Do not continue these checks in unsafe conditions. For immediate danger, use local emergency services and the device’s emergency instructions. Otherwise, contact your provider or a qualified technician.

What to tell support

Write down your exact model, service provider and on-screen message. Photograph the existing connections for your own reference before changing anything.

Original troubleshooting guidance based on the official sources below. Menu names can change. This is an independent guide, not a manufacturer service bulletin or a bench-tested repair.